Set your multimeter to ohms and insert a probe on each large terminal with the key off and the cart direction switch in the neutral position. Press on the accelerator with the cart’s movement control in the forward position, and the key is turned on. A click should be heard first from the solenoid.
How do you fill the battery in a golf cart?
- Your golf cart batteries need water. Depending on use, the batteries should be checked at least once per month. Remove the caps from the top of hte battery. IF the cell needs water, fill the battery to just below the ring in the cell neck using distilled water. Only add water to a fully charged battery.
How do you bypass a solenoid on a golf cart?
Bypassing Golf Cart Solenoid Method If you do decide to bypass the solenoid, this is what you need to do: Take the two larger wires that connect to the solenoid and connect them directly (keeping all safety precautions in place). This should do the trick and if it does not work then the solenoid is not the problem.
How do you test a solenoid on a 36 volt EZ Go golf cart?
This can Also be tested by putting a test lead on each small terminal and pressing the gas pedal. The meter should read 36 V when the gas is pressed. If this voltage does exist when the gas pedal is pressed then the solenoid should click and engage.
What happens when a solenoid goes bad on a golf cart?
When driving a gas golf cart with a damaged solenoid, the larger contacts may fail to release. When this happens, the starter keeps on operating, even when the ignition switch is turned off.
How do you bench test a golf cart solenoid?
Set your voltmeter to measure ohms, and place a probe on each large terminal (see image below). You should have a reading of 0 to 0.4 ohms. Anything higher, and it means that the solenoid has faulty contacts and should be replaced.
How do I know if my golf cart solenoid is bad?
If your golf cart fails to turn on when you turn the key on, this is the most obvious sign of solenoid failure. The solenoid clicks a little with the ignition system in regular operation; in most cases, a failing solenoid will not snap.
How do you test if a solenoid is working?
Do your best to listen for a “click” noise. If the click is strong and loud, it most likely means the solenoid has enough power and is working properly. If the clicking you are hearing is quiet or repetitive, it may be that your solenoid is not strong enough or does not have enough power from the battery.
Why is my solenoid not clicking?
If you do not hear a click, the starter solenoid is likely not functioning properly. Hearing clicking without the starter motor moving means the solenoid is transferring the electricity, but it may not be enough. No clicking means the solenoid is not properly engaging, but this may also be due to a dead battery.
How do I test my EZ GO sensor?
Put the key in the “On” position in your Run/Tow switch on the cart. Switch the F/R switch into a forward position to test your cart. Place your voltimeter testing pins on the throttle pins to see how much voltage you get. When the cart is running with no throttle, you should get about 10 volts here.
What are symptoms of bad solenoid?
4 Signs of a Bad Starter Solenoid
- Engine Doesn’t Crank or Start.
- No Clicking Noise When Trying to Start the Engine.
- Starter Spins Without Fully Engaging the Flywheel (Rare)
- Engine Cranks Slowly (Rare)
- Test the battery.
- Check That Power is Getting to the Starter Solenoid.
- Test the Starter Solenoid Itself.
How can you tell if MCOR is bad?
If you see it jump around (ie. 17% up to 30% or back to 10% erratically) you have a bad MCOR. If you don’t see it go all the way to 100% you have a bad MCOR. If it takes forever to start showing movement then quickly spikes up way past the low numbers, you have a bad MCOR.
Can a bad solenoid drain your battery?
If your starter solenoid has a weak short, that could deplete the battery.
How do you test a solenoid on a club car?
First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn’t move, then the problem is not with the solenoid. If it jumps and displays full voltage, then the solenoid is the problem and should be replaced with a new one.
Where is the reset button on a golf cart motor?
First, you’ll want to reset your motor. Get out your handy screw driver and work to uncover the motor itself. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor.
Why does my electric golf cart have no power?
Like any electric vehicle, the battery is often the root of the problem. If you go to start your golf cart and nothing happens, this is the first place to check. If the cart goes without charge for a long time, the battery may lack the minimum voltage required to restart. Batteries also lose their efficiency with age.